Sign in

OBD adapter: Check Engine codes, gauges and trip recording

Plug an ELM327 Bluetooth adapter into the OBD-II port and Autoracle reads engine fault codes, the VIN, battery voltage and sensor readings, while Orik explains what a code means. With the adapter the app records trips by itself, warns you about overheating and helps you check a used car before buying.

Check Engine on
P0171System too lean
P0420Catalyst efficiency below threshold
Battery12.6 V
Trip recorded · 42.3 km
In short
  • Autoracle works with ELM327-based OBD-II Bluetooth adapters with Bluetooth 4.0 / BLE; for now, in the Android app.
  • Diagnostics, gauges, trip recording and the pre-purchase check are free; having Orik explain a code is a chat message paid in credits (Orik Pro).
  • The app only reads the car’s data; the one thing it changes is clearing fault codes — when you tap it and after a warning.
  • Trip recording keeps going with the phone locked; a trip goes into Trips only after you tap “Save trip”.
  • The pre-purchase check shows how many kilometres and warm-ups have passed since the codes were last cleared, and permanent codes that a scanner can’t erase.
  • The fault code history is visible in the service book and to a buyer via the QR code only if the owner turns that on; by default it isn’t.
Free

Which OBD adapter you need and how to connect it

You need an ELM327-based OBD-II Bluetooth adapter with Bluetooth 4.0 / BLE — it plugs into the car’s diagnostic port, usually under the steering wheel on the left. Most cars sold in Europe from around 2001 (diesels from 2004) have an OBD-II port; check for your own car.

  • Plug in the adapter and switch on the ignition.
  • In the “More” sheet → the “OBD” group → “Connect an OBD adapter” → “Find adapter”. Android will ask for access to nearby devices (Bluetooth).
  • Pick the adapter — the first connection takes up to 20 seconds. After that the app connects to it by itself and restores a dropped connection without you.

After the first connection the “OBD” group gets four sections: “Diagnostics”, “Gauges”, “Pre-purchase check” and “OBD adapter”. All of it is free. Step by step — in the help guide.

Adapter not found? Check that it sits firmly in the port, the ignition is on and Bluetooth on your phone is on.

Step by step in the help guide

Free + Pro

What a Check Engine code means: fault codes and Orik’s explanation

The “Diagnostics” section shows whether Check Engine is on, plus the fault codes: confirmed and pending — ones the car has already noticed but is still checking. You can read codes as often as you like, for free.

Each code has an “Ask Orik” button. It opens a chat with Orik with a ready question: what this code means for your car, how urgent it is and what to check. Orik answers with your make, mileage and service history in mind. Whether to send the question is up to you; a message costs 1 credit (Orik Pro).

Freeze frame — the car’s readings at the moment of the fault: speed, rpm, temperature and others, if the control unit saved them. If the fault appeared while a trip was being recorded, the app also adds its own minute of readings before it. The freeze frame goes to Orik together with the code and helps understand under what conditions the fault happened.

I explain what usually lies behind a code and suggest what to check. But the final diagnosis is the mechanic’s — show them the codes.

Free

Can you clear fault codes yourself?

Yes: the “Clear codes” button in “Diagnostics” turns off Check Engine with the standard OBD command. Before clearing, the app warns you: if the cause isn’t fixed, the code will come back, and the inspection readiness monitors will reset too — the car will need some driving to set them again.

The codes are saved to the history before clearing (if it’s on), so nothing is lost — you can show them to a mechanic later. If the car doesn’t confirm the clear, the app says so: try with the ignition on and the engine off.

Apart from clearing codes, the app changes nothing in the car: no coding and no writing to control units.

Free

Gauges, VIN, mileage and battery from the car’s data

“Gauges” show speed, rpm, engine temperature, fuel level and voltage in real time. Below — “More from the car”: engine load, oil and air temperature, fuel trims and other parameters — only the ones your car reports.

  • VIN — “Save VIN to car” if it isn’t in the car details yet. On locally assembled cars the control unit’s VIN may differ from the documents — then tap “This is my car” and the app will remember it.
  • Mileage — if the car reports it (many cars have no such standard command). The reading is saved with a button, and with the “Update mileage from car data” switch — by itself once a day, so the service schedule is calculated from the exact mileage.
  • Battery — from trips recorded with the adapter: voltage after parking, the dip when the starter cranks and charging while driving. If the voltage drops below 9.6 V when starting, or the dip has grown noticeably over a month, Orik will mention it in “Orik noticed”. Voltage from the adapter is a guide, not a precise instrument: have the battery tested at a garage.
Free

How to record a trip automatically

Trips has “Record a trip”: the app itself records the time, kilometres and stops. With an adapter — from the car’s data (speed, rpm, fuel consumption if the car reports it), without an adapter — by location. The route on the map — with the “Record the route” switch.

You can lock the phone: while recording, the “Orik is recording your trip” notification stays in the notification shade. A stop for fuel or coffee doesn’t end the recording — drive on and the trip continues; after 2 hours parked the recording ends by itself. At the end — a draft: the category (“Business” or “Personal”), the purpose — and “Save trip”. Without that tap nothing is saved.

You start a new trip yourself with “Record a trip”. With an adapter, a trip you started isn’t cut short: in the “Wait for the adapter” mode, after the engine was switched off the app reconnects to the adapter and carries on recording by itself, even if it was closed; in the “Via car audio” mode, if the trip is paused and the phone connects to the head unit, you get an “In the car?” notification — tap it and recording continues.

A saved trip goes into the trip log with its cost. If the car reports fuel consumption, the trip’s litres are taken from its data and checked against your “to full” fill-ups; “Statistics” shows how long the engine ran standing still and what that cost.

Step by step in the help guide

Free

Warnings on the road and the parking spot

While a trip is recorded with the adapter, Orik sends a notification if something goes wrong:

  • the engine is overheating — from 110 °C;
  • the alternator seems not to be charging — voltage below 12.8 V with the engine running;
  • Check Engine came on or a new fault appeared — it’s saved with a freeze frame in “Diagnostics”.

Engine switched off during recording — the app remembers where the car is parked in “Where I parked” (the “Mark parking spot when engine is off” switch; location access needed). The fuel level went up noticeably — you’ll get “Looks like you refuelled”: tap it and take a photo of the receipt.

Free + Pro

Checking a used car before you buy

Viewing a used car? Plug the adapter into its port, switch on the ignition and tap “Check the car”. The main thing the check looks for is signs that the codes were cleared just before the viewing.

  • How many kilometres, warm-ups and engine hours have passed since the codes were last cleared — if it’s only a few hundred kilometres, that’s a reason to ask the seller.
  • Permanent codes: a scanner can’t erase them; the car clears them itself only after a repair.
  • Incomplete self-tests, Check Engine and the distance driven with it on, fault codes and pending codes.
  • The VIN and mileage from the control unit against the ones you entered from the listing, and the battery voltage.

The result is a traffic light: “No obvious signs of a reset or faults”, “Questions for the seller” or “Careful: there are serious signs”. You can send the report with the “Share” button, and “Ask Orik” (credits) suggests what to ask the seller and what to have checked at a garage. The check is free, changes nothing in someone else’s car and is stored only on your phone.

The adapter sees the engine control unit, but the body, rust and suspension — only your eyes. Take an inspection checklist with you.

Free

Fault code history in the service book and for a buyer

Every code reading is saved to the history: date, mileage, Check Engine, codes and freeze frame. You can turn the history off with the “Keep fault code history” switch, delete individual records, and “Share history” sends it as text, for example to a mechanic.

Two switches on the car decide who else sees it: “Show in service book” and “Show to buyer” — on the history page via the QR code. Both are off by default: a history without faults adds trust, but you don’t have to show everything.

Free

What data the app reads and where it’s stored

Our server receives the fault code history (while it’s on), the VIN and mileage — when you saved them or turned on “Update mileage from car data” — and recorded trips, after “Save trip”. Live readings, battery measurements, fuel level and checks of other people’s cars stay only on the phone.

For trip recording, location is used only while recording is running (route and kilometres) and at the end — for the parking spot, if that’s on; the app doesn’t ask for “always” location access. Details — in the privacy policy.

Frequently asked questions

Frequently asked questions: OBD adapter: Check Engine codes, gauges and trip recording

Which OBD adapter will work?

An ELM327-based OBD-II Bluetooth adapter with Bluetooth 4.0 / BLE. The app doesn’t find adapters with only classic Bluetooth or Wi-Fi.

Does it cost anything?

No: connecting, fault codes, clearing, gauges, trip recording and the pre-purchase check are free. Only asking Orik what a code means costs credits (Orik Pro): 1 credit per message.

Does it work on iPhone?

Not yet: connecting an OBD adapter works in the Android app. A Bluetooth adapter can’t be connected in the web app.

Can the app damage my car?

The app only reads data. The one command that changes anything is the standard fault code clear, and only after you confirm it. There is no coding and no writing to control units.

Why can’t the app see the mileage?

Most cars have no standard OBD command for mileage. Then mileage is entered as usual — with fill-ups, workshop visits or a mileage check.

Does trip recording drain the phone battery?

Recording by location and the connection to the adapter use battery, like a navigation app. Without a trip you started, the “Wait for the adapter” mode uses no battery; neither does the “Via car audio” mode, as long as the phone isn’t in the car.

Try it with your own car

All tracking is free forever. Photo recognition and Orik the assistant — 3 days of Pro free after sign-up.

Open the web app Google Play Coming to the App Store

Pricing →